Tuesday, 15 February 2011

Thats gotta hurt!

Practice makes perfect so up to the quarry on Saturday to get used to the bike over the bigger rocks, I also took the chance to fine tune the carb. The Villiers set up I have is just about spot on but a little movement on the airscrew coupled with the lower gearing had the bike moving very slowly, smoothly and consistently on tickover especially on descents the trip to the quarry also gave me chance to ride with the new tank for the first time, I wanted to make sure that it was clean inside so i ran THREE fuel filters! and it gave me the opportunity to find out how much fuel the tank held, as it turns out a little under 3 litres of which about a half litre is reserve, more than enough for a single venue trial.

Full of optimism that even a rain fall of Biblical proportions could not dent  I set off at Addingham Moorside for Yorkshire classics second Championship round.
The venue is notoriously rocky and peaty so I set off early to get the best of the sections blazing a trail yet avoiding the gooey mess that some sections would inevitably become.
The first was a simple affair in and out and over some benign rockey and although the second was a staple of the venue I fell foul of it and dropped into the stream and stopped dead... ouch. A precautionary dab on the third then a run of cleans until i three'd my way out of Mick Driifield's steep rock gully and that was it for that lap.  I cleaned the tricky 7th and found a cracking route in 8 up and over a massive boulder that others rode around section 8 I chose the hard route as the clubmans route had some tight turns to avoid the loose rocks that I personally felt comfortable riding over, lap 2 was even better I only dropped the one until section 8 when disaster struck,  the clutch seemed to drag then the rear brake locked on , going up hill,, and ouch the chain wrapped itself around the gearbox sprocket and lifted the chain case up destroying the lugs on the gearbox..


I had the bike to bits in a jiffy but could nt find anything obviously amiss until I put it together again and noticed that the rear wheel had about 20mm of sideways and vertical movement even when bolted up tight.. I assumed the Sherco alloy spindle had cried enough

Back home  I had the thing in bits and I had to apologise to the spindle, it had borne its weight and more in the breakdown, the culprit was the nearside rear wheel bearing which had had a catastrophic failure. The inner race had totally separated from the bearings and outer cage causing the rear wheel to move which lead to the chain jumping which preceded the destroyed gearbox mountings.

A couple of phone calls firstly to Simon Bateman Namtab who promised all the clutch bits and bobs would be in the post later that day and to the benevolent Ady Brayshaw who agreed to sort some alloy welding of the gearbox lugs with the box in situ.. that though will have to wait till next week as this week other projects dominate! in the meantime the pics show clearly the damage to the gearbox lugs and the clutch been stripped down ready for Simon's delivery!

As for the trial another great trial from Yorkshire classic and befitting of the best pre 65 trials club in the country, a decent entry in horrble weather at a venue renowned for rocks all the sections were rideable yet challenging and all cleanable with care and skill and a half decent bike!

Thursday, 10 February 2011

Chain reaction

One of the issues carried over from the original bike was ''what exactly is the chain size'' and the state of the rear sprocket. The chain was a Renolds with no size markings and an old 420 seemed the right thing but it was hard to state 100% as the rear sprocket was so well worn, however a new 420 chain was just a fraction too tight on the teeth, it fitted but was a little 'clingy' so we used a 428 std  chain in its place
This was ok although the clearance for the spring link was a little fine so rather than have the link to the outside it was mounted inboard temporarily.

Wanting a final solution I was prepared to put new chain and rear sprocket on, the only issue been where to get a sprocket certainly not off the shelf and then from the inter-web up popped  'Sprockets Unlimited'

All they asked was that I choose chain size .. 428 easy that bit, No. of teeth.. well original was 58 but as as some old wag at a trial suggested it was a tad highly geared I plumped for 60 this time.  centre diameter.. now the original is a SUNG fit round the brake and even has a little machined off to make way for the bolts so out with the micrometer and a figure was agreed (after measuring 5 times to be certain) Then the bolt centres... again measured five times, they have to be spot on..

I've recommended other suppliers on this site before but these guys take the top award,  in less than a week the thing arrived absolutely SPOT ON no margin of error whatsoever . It bolted straight on, very impressed. and the extra two teeth only add 8mm to the diameter so only the engine will know the difference.

As I bolted the wheel back in I took the time to add a 3mm spacer to the drive side spacer just to move the chain over and more easily clear the clutch case. If this is succesful I'll machine new spacers for the rear axle, I'm especially keen to make the one for the offside like a cup to offer some protection to the exposed bearing on that side of the hub.

Friday, 4 February 2011

night of the big hammer..

Having  a vaulted ceiling space in the garage has been great for storage it does though have two downsides, firstly when the heating is on it rises up to the eaves keeping the pogo sticks, strimmer et al nice and cosy whilst I suffer in the cold! Secondly although a couple of 58 watt 1.5 meter strip lights are okay, they don't give all the light I crave. Armed with half a dozen sheets of plaster board 10 down lighter and 25m of two core 1.5mm cable and a wiring diagram from my sparky I set to work, and now I have a half complete ceiling complete with 5 down lights over the work bench and I can see clearly ( which is certainly not the verdict my optician offered this morning!)

Following last weeks very rocky trial at Nab End  near Sowerby Bridge I've a couple of issues to deal with.  The new bike stuff,  are the steering bolt needs re adjusting as it comes loose and yet the bolt does'nt seem to have turned so I assume that the taper rollers are bedding further in through the grease, tightening it all up isn't an issue though loosen the yolk bolts, the top snitch bolt and away you go.. 30 seconds of a work plus an hour talking to a neighbour and the jobs done.

There is a pretty nasty noise coming from the chain case so that will have to come off I suspect that the  case isn't on quite right and one of the edges is touching the clutch basket.

The only damage in the trial was to the rear brake lever it took a bite out of a Yarkshire rock and came off second best, so out with the lump hamme, off with the arm and into the big vice, a bit of swearing and hey presto as good as new!

total cost for the weekend
£ 10 join club ( annual fee)
£ 10 entry fee
£ 2.60 2 litres of petrol

Even bigger hammer called for!!
The nasty chaincase noise has been resolved ( hopefully), whipping the cover off the damage was easily visible. The 37a chaincase has little in the way of clearance for the clutch basket and the tangs of the clutch plates and for reasons unknown the little blighters had been rubbing on the inner chaincase. A bit of head scratching and the solution/ reason  wasn't obvious until I tried to refit the case and it would'nt quite go back. The lower case guard at the front of the engine had obviously taken a bit of a thump and moved the outer back by a couple of mm. So in true Yorkshire style out with a delicate lump hammer and seven bells of s##t later and it was back in place allowing the case to be refitted exactly right and thus no more nasty noise .. ding dong!
In metal working mode I had a long bout of a good case of looking at as the brake rod caught my eye and it rubbed the rod in the shock so in the vice with it a natty kink was added and it looks good and does the job
..

Wednesday, 2 February 2011

first time out...

Having had extensive post build testing (started bike and pushed it in the back of van) I lugged the bike up to Yorkshire Classic  1st Championship round at Deer Park/ Lady Lane Bingley. 2011 trials
Renowned for rocks and slippy climbs it would prove a decent testing ground  and so it did .

Been the first round of the year there was a fantastic turnout from dabbers such as octogenarian Bill Hill to respected modern bike riders like James Noble, as well as the usual eclectic mix of former works riders, collectors, enthusiastic hopefuls and those who should know better.
The bikes reflect that to, for all the issues elsewhere on eligibility, here's a sensible approach with everything from very trick 2011 cubs to pulled out of the barn oily rigids all broadly within the clubs clear rules.

With riding a new bike and with the venue having a reputation as getting tougher the later you ride I set off smartly and was probably in the first three to do the first half dozen sections. At that point it was obvious that the clutch was slipping badly and that the rear wheel needed tightening up so a quick ride back to the van had the clutch adjusted and the rear spindle adjusted and we were off ( a little too quickly!) the next sections were on the long ride out over the moor in the stream that in previous years had dried up to an almost desert like state of loose dry rocks. However as global warming slips by West Yorkshire the stream was FULL of water and proved a decent test on the steep slippy climb out.

Now the quick 'pit stop' played its hand as I started the second lap and just before I started section 4 with its very steep descent I looked down and saw the rear brake steady was loose ( come off actually) so returned to the van for more 'tweaking' ie new bolts! official photos of the trial

So for a first time out the bike had had some drama but overall the ride was positive the longer wheel base over the Banvill was noticeable on helping to keep to a line and yet the bike still turned well and without the front wheel tucking in. the engine, been a direct transfer was brilliant, I could' nt ask for more (I've no doubt others might but for a dabber it was more than adequate) the fork angle was commented on as steep but having given it a good coat of looking at I think that's down to the yolks which pull the stanchions in a smidge.( don't know if you can see in the snaps.) I do have another pair of billet yolks in the workshop but unless its a problem that's where they will stay.

 So back home quick wash of the bike oil the chain and shes ready to go again.. who said old Brit bikes need lots of attention... as for the rider  Doh! must do better, lose weight, pay attention, get fit, practice more...  the usual excuses.. importantly theres always tomorrow.

Without the file to hand I've put some snaps on from Keighley Gate Preunit trial at the end of last year.. the keen eyed will spot the money grabbing observers building thier college fund!

Friday, 21 January 2011

Brake!

Something I really wanted to get right was the position of the rear brake lever so that it was spot on. No tipping the foot forward or having to lift the foot to get to. With the new bracket welded in place the lever was modded to suit, the bush was reduced in length and the pivot point likewise so that they would not stick in the heel of my boot and the  lever itself was 'persuaded' to change profile with a little Yorkshire technology  ( 3lb lump hammer)
To get the pedal to rest at the right level Ady had welded a small piece of steel to leg of the rear sub frame and half an hour with the file had a small but perfectly formed and positioned stop
I also took the grinder to the edges of the lever to smooth them off so that the precious boots don't get caught.
In the coming months once the bikes running I'll develop this pedal further with a little reshaping and some 'drilling' as nothing weighs as little as a hole! 
The next step was sorting out a brake rod / cable. I originally favoured a cable as it has to run through the rear shocker spring, and I hoped there would be less chance of fouling if I used the cable. Unfortunately the amount of 'stretch'  in the cables I tried was unacceptable, so a more traditional rod was called for. A length of 6mm stainless rod was threaded at both ends and suitable fittings pilfered from the parts bin ( actually a 100 litre plastic cistern briming with ' previously loved' stuff looking for a new home)
Movement from 'off' to 'full on' is approx. 15mm so it works well and with a little work will look just as good, until then function is king.

Progress!

Well with the snow finally melting and more importantly the temperature rising above zero (briefly) and finally the introduction of heating in the garage progress has moved on so that the bike is now ride-able!
The first thing that needed resolution was the brake pedal. Although a pedal had been bought with the frame it was unsuitable ( wrong size pivot hole, arm was too short and had less than 5mm movement when mounted before it hit the foot rest) so alternatives were checked out and the neatest solution was to use a Sammy Miller tiger cub stainless lever from the parts bin and reposition the pivot point on the bike.
The very amiable Ady Brayshaw in Halifax 07984 160944 quickly had the new pivot point welded neatly to the bike and whilst he did that I checked out a very nice TY80 tank that he had just painted in petrol proof two pack. The conversation moved to how I was going to paint the frame and Ady agreed to do the job himself the next day and have it back to me within 24 hours for a very reasonable sum. The only downside was that I'd have to have the dry build complete and the bike stripped and back to Ady's within 24 hours...

Monday, 4 October 2010

The man that can..

One of the essentials of pre 65 trialling is knowing someone who knows whats what what works and what doesn't. I 'm fortunate to have one on my doorstep, the other is knowing a 'man who can 'so that when your muse tells you to head off in one direction you have someone to hand who can make stuff ( well is essential, quickly is good, cheaply is fantastic!)
Access to a decent lathe and knowing how to use it, an industrial pillar drill and a stock -pile of various metals in sheet, rod and tube are all strong qualifications so step forward my father.
Normally happily making model steam engines ( stationary, rail and marine) or sailing or running them, he can usually be persuaded to produce some fantastic pieces of bespoke metalwork such as bushes, spacers and tube etc. all to your specific requirements. Over the years we have found that rather than working to drawings and measurements it is much more accurate to build to fit. Especially so on sthings like swinging arm bushes where the present dimensions may be far from what they were originally. and where two formally identical round holes are no longerround nor identical.

So to the depths of the Lake District I travelled armed with a box of aluminium sheet and rod plus the bike as it stood so that we could 'make to fit' . Hopefully at the end of the day iIwould have pre load spacers for the forks, spacers for the rear spindle, an original pre 65 rear brake plate that fitted the Sherco 17mm spindle and various other spacers.

In the space of a couple of hours we had the rear spacers turned on the lathe and drilled out for the 17mm spindle and they fitted first time! We made up mock ups with 22mm copper tube to get the right lengths so that the wheel was centred and the chain ran true then replicated them in alloy. The off side was simple as it is single piece and on the chain side we cut two pieces so that they and the brake back plate made up the required distance and bingo..
The brake back plate soon became the owner of a 17.5mm hole.

i have earlier said that the forks ran great and they do but they do 'sometimes' have a tendency to drop a quarter of an inch upon putting weight on them. I believe that this was because i was using an old valve type spring in each one as a preload spacer. Springs being what they are I suspect that they moved a little and became unseated so we made up a couple of 'top hats from alloy to do the job instead and popped them in.. As near as dammit the same sag and suspension movement so we'll try them ( movement of the old valve springs was approx 5mm over their 35mm length so we opted for 32.5mm long spacers as a mid point)

I think i also mentioned earlier that some of the brackets were 5 - 10 mm too wide so we made some tube to use as spacers rather than packing the gaps with washers.. I ended up with 8,10mm and 3/8 of an inch i/d tubes with an o/d of 15mm.

a nice days pottering and a decent lunch thrown in!

Saturday, 2 October 2010

Shopping list..

Well firstly some photos from my design board of what it is I'm building, most of the bikes I've photographed myself at Yorkshire Classic trials or at the Pre65 SSDT. the style I am trying to recreate is best exampled by the top bike. Mine will almost certainly though have white plastic guards front and rear as well as an alloy tank with a white crescent.

Just to even things up a bit after posting the last update I realised i'd missed a few suppliers out.. so best pop them in to create a fair view of whats been bought.. no expenditure figures until the end so that in best 'Grand Designs' fashion I can boast of only using 80% of my contingency fund!

Anyway more bearings via ebay from EBR, 18mm with 13mm shank drill bit via ebay from Uk Drills ( this for a fantastic piece of bespoke metal work and fabrication from the countries leading steam boat engineer! more to follow in a special piece soon) rubber washers from Naoutlet All these suppliers delivered within 48 hours of making a Paypal payment.

Finally the only personIi've done face to face business with the brilliant Andy at Pennine Trialsport although not specifically into pre65 or twin shocks he has a fantastic background knowledge and is more than happy to root through his parts bins for something off the peg! the bike now sports a GasGas chain tensioner and an aluminium  Sherco rear spindle that weighs a third of the originally proposed steel one. all thanks to Andys' perseverance.( and they fit first time with no modification!) to complete the theme i'm searching for something from the other three manufacturers that will also fit the bike. ( Beta, Scorpa, Montesa)

The rear spindle did give us our first 'proper' engineering problem/ solutions and when I have a moment I'll go a little further but it did involve a 180 mile round trip and a day out in the Lake District..

Photos..well I've taken loads on my new Nikon all I have to do now is get the pooter and camera to speak to each other, so when they come they will probably all come at once..

How much is scrap aluminium worth?

The postman and UPS have been busy and have dropped off a load more bits and bobs for the bike including spherical bearings for the shock lower mountings, imperial bolts for the engine mounts, rubber washers to mount the rear mudguards and a  rear brake pedal.

I spent a couple of hours head scratching trying to work out how to fit the brake pedal, but as it was built for the frame buy the frame builder and 'bolts straight on..' I assumed that it would .. however the bolts used are larger than the mounting, the arm fouls the sub frame, the mounting fouls the footrest mount, the total movement is only 12mm and the actuating arm is about 60 - 75 mm too short.. so it probably wont see the light of day..

On the other hand small stuff arrives by the bucket and is 100% correct just as ordered. Big shout  out to Namrick for thier imperial nuts/bolts and Simply Bearings for the spherical bearings ( they have a handy calculator on thier site which tells you what size bearings are available, you tell it what sort you want and one of the dimensions and it does the rest) still not quite as impressive as the man at Rochdale Bearings who armed with a well thumbed reference book found the right mix of imperial and metric sizes for the steerer bolt.

So the engine/ box came out and the bolts were machined to length, half the head of the lower mount has to be machined off so that it can clear the chain case. I opened up the engine mounting holes on the rear mount as they were slightly adrift of where they should have been. opening them up to 12mm sorted that out. The engine protector ( a piece of bent bar that protects the front of the chain case) fitted spot on via the front engine mounts.

Then out with the file and Dremel to fabricate an alloy bracket that holds the clutch adjusting screw, the exhaust mounting and with a little thought serves also as the lower mounting point for the rear mudguard! starting off looking a little agricultural within 4 hours it looks smart but importantly is functional and easily adjusted etc. the only downside is that the floor of the garage the workbench and I are all covered in about a hundred weight of alloy filings. Time for the sweeping brush!

Wednesday, 29 September 2010

Airfix kit with no instructions and with some pieces missing!

The plan was to dry assemble everything, so that i knew what went where, what fitted what needed doing to what etc before any paint or powder coating was applied to anything. this meant that the build may take a little longer but that when final assembly came along everything would fit as i'd already fitted it once before.
first things first preserve the frame.
as picked up from the M6 it was in bare metal with its bronze brazed joints loud and proud. There was plenty of flux visible so as soon as it landed in the garage i took out the plumbers  Yorkshire Pad and gave the frame a good rub down to clear the flux and and slight surface corrosion.
this gave me a chance to give the frame a close inspection and a good coat of looking at. first impressions were that the brazing was first class and that the joints were all well made with no lugs in sight. the headstock was long ( circa 150mm) and wide (52mm) compared to my previous cub and bantam frames and that at the rear upper shock mounts the bike seemed quite wide about 40mm wider than both cub and BSA yet narrower at seat/ tank junction than both by about 10mm. 
the rear shock position seemed more 'laid down than both the other bikes and the 'engine room'  significantly shallower than both bikes ( at least 25mm) overall the impression was of a strong frame with robust proportions that coupled with the T45 tubing would make it up to the job of supporting my svelte like 100kg frame!
I'd hoped that removing the motor from one bike it would drop cleanly into the other and initially this seemed to hold true withe the engine complete with carb lifting cleanly into the frame of the James/FB. the reduced height was immediately confirmed but was adequate with no immediate issues. the front engine mount was perfect the bolt went straight in, and the middle/lower seemed to do the same , unfortunately the rear was approximately 5mm out and the engine mount would require re drilling also concernedly the mount was 3 mm too wide on the near side of the bike and 4 mm too wide on the off side.checking the lower/ middle mount I found that although the bolt holes were perfectly in line the off side Mount was approximately 8mm too wide.
the lower mount was easiest to solve by maching a spacer from 5/8 inch aluminium rod/ bar. the rear mount is more complex as it is also the mount for the clutch cable and silencer.
on to the biggest looking issue was the size of the headstock it was about 25mm longer than either of my existing bikes and thus seemingly too long for either of my bolts on the.other bikes. setting that aside it was massive internally compared to the other bikes the cub and BSA both having and id of circa 42mm the james/fb was 47mm. Alan had recommended a bearing size of 47x25x10 sadly that was never going to fly as both my head bolts are imperial sized 3/4 inch which comes out at 19mm give or take. 

Tuesday, 28 September 2010

nuts and bolts

For ease of maintenance in the garage and especially 'in the field' I want to have as uniform as possible fasteners. I want where possible to reduce the number of tools required , both in the garage and  in the pocket whilst competing.
I have chosen to go for A2 grade Stainless steel, metric ,button headed bolts, washers and nyloc nuts where ever possible.
Button headed so that I don't need two 12 mm spanners just one and an Allen key, so that the head has the lowest and smoothest profile yet the largest contact area and A2 stainless steel for corrosion resistance ( the more durable in A4 was excessive in spec. ( sea water) and cost!)(+ 30%)  and finally metric as it is the most commonly available size.
Finding all the fasteners required for the frame set proved relatively simple locally at Screwfix.com and even the counter sunk screw for the GasGas chain tensioner proved no problem via ebay.co.uk
As for length of fasteners each has been machined to an optimum length to leave a complete thread outstanding from the nyloc nut when the fastener is secured.
The most complex bolts to source have been the three engine mounts, although drilling out the frame to a metric 10mm was not an issue, I felt that drilling out the cast alloy mounts on the engine  cases was perhaps taking a risk and one that carried little or no value so I stuck with the ioriginal sized fasteners.
After several days looking i found Namrick.co.uk in the UK who specialise in imperial sizes for classic cars, they have something of most threads although some  are now in limited supply as traditional automotive threads are been discontinued even in the US.  There are in fact many stockists in the USA but import duties and fees proved prohibitive.
So 3/8 inch bolts and nuts were obtained eventually but unfortunately were not /are not available in Stainless steel in the correct lengths of circa 90 -100 mm so zinc plate and traditional hex heads  it is.

Sunday, 26 September 2010

Meet you on the corner!

Having searched high and low for a contact no for Alan Wright 'Classic Dirtbike' http://www.classicdirtbike.co.uk/ and Trials Central http://www.trialscentral.com/forums/index.php both came up trumps. Amazingly I got through to him straight away and a deal was done over the phone for a frame swinging arm. spindle, bash plate and brake pedal the only catch was he was going to the Isle of man the next day for the two day trial so my only chance to get the thing relatively quickly meant meeting up in a service station en route!  long story short.. we finally met on a roundabout! and I took delivery of a new frame etc. in the first week of September. I had an ambitious plan to move everything from the Banvill across to the new frame and be riding the new bike in the Yorkshire Classic Trial the first week in October..   oh how quickly optimism fades!!

A germ of an idea


Add caption

Matthew and I had been up in Scotland for the Pre65 and SSDT at the beggining of the year and in the West End car-park Alan Wright had amongst all his other stuff some Pre65 bits including a James/ FB frame set and other associated bits. I checked them out at the time just out of curiosity, as a year or two earlier (2006 to be exact!) i had snapped his bike at the Pre65 minus paint/powder coating. See the photos alongside.

Monday, 20 September 2010

New Dawn!

On the Banvill, YCMC  November 16th 2009..
The time has come to freshen up the 'Banville' and sort out some of its inherent issues.
The engine and forks are great ( 37a and Mazzochis inside 'cub' legs) However the frame is too short ( wheelbase is approx 48.5 inches) the foot pegs are too high and the rear shocks are under sprung ( it has circa 2 inches of sag when i sit on the thing and most riding conditions have the springs almost fully compressed!)

Having checked out the dimensions on my Beta Rev3 to try to have a similar riding position I can see that some drastic chopping / fabricating of the Bantam's modded frame would be required and then re powder coating the whole lot. The swinging arm spindle is supported by bronze bushes which although recently replaced and still as new, this frame is possibly at the extent of its life in my hands.

So armed with a drawing board, pencil, tape measure, micrometer, credit card and an exhaustive trawl of the Internet for inspiration I have decided to build a James /Francis Barnett replica.

The FB concept holds more attraction to me as 'everyone' has a James (must be a red thing) and FB were regarded in the 40's and 50's as being a a well engineered bike. However the adoption of the AMC unit for power in the late fifties meant that as trials bikes in the early 60's they were unfashionable and simply useless! 1962 though had the 'works' using the 32a/37a motor. At the end of the day the only difference was the tank badge and frame colour red vs Ardent Green..